碟片式离心机日常怎么保养？

离心机主要用于分离悬浮液中的固体颗粒和液体；或者将乳化液中两种密度不同的不相溶的液体分开（例如将奶油与牛奶分开）。那么，碟片式离心机日常怎么保养？

How does disc type centrifuge maintain daily?

Centrifuges are mainly used to separate solid particles and liquids in suspension; Or to separate two insoluble liquids of different densities in an emulsion (e.g. cream from milk). So, how to maintain the disk centrifuge daily?

碟片式离心机日常怎么保养？

1、离心机运行前，请切断电源，松开离心机制动器。你可以试着用手转动滚筒，看看有没有咬人的地方。

2、检查其他零件是否松动和异常。

3、打开电源，顺时针启动汽车。

4、通常每台设备到厂后都要空运转3小时左右，没有异常情况才能工作。

5、材料应尽可能放置均匀。

6、需要有人操作，容量不得超过额定容量。

7、严禁机器超速，以免影响机器的使用寿命。

8、机器启动后，如有异常情况，需要停机检查，必要时应拆卸修理。

9、离心机运转速度很快，所以你一定不能用身体接触它的滚筒，以防发生意外。

10、滤布的目数应根据被分离物料固体颗粒的大小来确定，否则会影响分离效果。

11、密封圈嵌在滚筒密封槽内，防止物料跑合。

12、为确保离心机正常运行，请每半年对转动部件进行加油和维护。同时，检查轴承的运行润滑有无磨损；制动装置中的零件是否磨损，并认真更换；轴承是否漏油。

13、机器使用后，要清洗干净，保持清洁。

14、不要将非腐蚀性离心机与高腐蚀性材料分开；此外，严格遵守设备要求和规定。非防爆离心机不得用于易燃易爆环境。

How does disc type centrifuge maintain daily?

1. Before running the centrifuge, please cut off the power supply and release the brake of the centrifuge. You can try turning the roller by hand to see if there is a bite.

2. Check whether other parts are loose or abnormal.

3. Turn on the power and start the car clockwise.

4, usually every piece of equipment to the factory after empty operation for about 3 hours, no abnormal situation can work.

5, the material should be placed as evenly as possible.

6, need to be operated, the capacity shall not exceed the rated capacity.

7. It is forbidden to overspeed the machine, so as not to affect the service life of the machine.

8, after the machine is started, if there is an abnormal situation, it needs to stop the inspection, if necessary, it should be disassembled and repaired.

9. The centrifuge runs very fast, so you must not touch its roller with your body in case of accidents.

10. The mesh number of the press cloth should be determined according to the size of the solid particles of the material to be separated, otherwise the separation effect will be affected.

11. The sealing ring is embedded in the drum sealing groove to prevent the material from running.

12. In order to ensure the normal operation of the centrifuge, please oil and maintain the rotating parts every six months. At the same time, check whether the running lubrication of the bearing is worn; Whether the parts of the brake device are worn and carefully replaced; Whether the bearing leaks oil.

13. The machine should be cleaned and kept clean after use.

14. Do not separate non-corrosive centrifuges from highly corrosive materials; In addition, strict compliance with equipment requirements and regulations. Non-explosion-proof centrifuges shall not be used in flammable and explosive environments.

什么是碟片式离心机？

转鼓内有一组互相套叠在一起的碟形零件--碟片。碟片与碟片之间留有很小的间隙。悬浮液(或乳浊液)由位于转鼓中心的进料管加入转鼓。当悬浮液(或乳浊液)流过碟片之间的间隙时，固体颗粒(或液滴)在离心机作用下沉降到碟片上形成沉渣(或液层)。沉渣沿碟片表面滑动而脱离碟片并积聚在转鼓内直径的部位，分离后的液体从出液口排出转鼓。碟片的作用是缩短固体颗粒(或液滴)的沉降距离、扩大转鼓的沉降面积，转鼓中由于安装了碟片而大大提高了分离机的生产能力。积聚在转鼓内的固体在分离机停机后拆开转鼓由人工清除，或通过排渣机构在不停机的情况下从转鼓中排出。

What is a disc centrifuge?

A drum contains a set of disk-shaped parts that are stacked on top of each other - disks. There is a very small gap between the discs. The suspension (or emulsion) is added to the drum by a feed tube located in the center of the drum. When the suspension (or emulsion) flows through the gap between the discs, the solid particles (or droplets) sink down to the discs in the centrifuge to form a sediment (or liquid layer). The sediment slides along the surface of the disc and escapes from the disc and accumulates in the inner diameter of the drum, and the separated liquid is discharged from the drum through the outlet. The ROLE OF THE DISC IS TO shorten THE settlement distance of SOLID particles (or liquid droplets), expand the settlement area of the drum, because the disc was installed in the drum, the production capacity of the separator was greatly improved. The solids accumulated in the drum are removed manually after the separator is shut down, or discharged from the drum through the slag discharge mechanism without shutting down.