啊啊

NEWS CENTER

新闻动态

您现在的位置:
首页
/
/
/
污油泥处理:下面介绍下含油污泥处理工艺概述(Oily sludge treatment: The following introduction of oily sludge treatment process overview)

污油泥处理:下面介绍下含油污泥处理工艺概述(Oily sludge treatment: The following introduction of oily sludge treatment process overview)

  • 分类:行业新闻
  • 作者:
  • 来源:
  • 发布时间:2022-10-13
  • 访问量:0

【概要描述】污油泥处理:下面介绍下含油污泥处理工艺概述

  目前,中国含油污泥处理解决企业所选用的关键工艺有:热处理工艺、热洗、催化裂解、苛化、集中焚烧处理及制得浮选剂。之上处理解决企业在含油污泥储存、处理解决的状况下会导致工业废气、废水、污泥及噪声,对工业废气、废水及污泥务必进行相对应处理,后剩下来的废水、污泥还需要有的趋势。因此对含油污泥处理解决企业的监管环节,包括了储存、加工过程及污染处理机器设备

Oily sludge treatment: The following describes the following oily sludge treatment process overview

At present, the key processes selected by Chinese oily sludge treatment and solution enterprises are: heat treatment process, hot washing, catalytic cracking, caustic, centralized incineration treatment and preparation of flotation agent. The above treatment solution will lead to industrial waste gas, waste water, sludge and noise in the condition of oily sludge storage and treatment solution. The industrial waste gas, waste water and sludge must be treated accordingly, and then the remaining waste water and sludge still need some trends. Therefore, the supervision of oil sludge treatment enterprises includes storage, processing and pollution treatment machinery and equipment

污油泥处理:下面介绍下含油污泥处理工艺概述(Oily sludge treatment: The following introduction of oily sludge treatment process overview)

【概要描述】污油泥处理:下面介绍下含油污泥处理工艺概述

  目前,中国含油污泥处理解决企业所选用的关键工艺有:热处理工艺、热洗、催化裂解、苛化、集中焚烧处理及制得浮选剂。之上处理解决企业在含油污泥储存、处理解决的状况下会导致工业废气、废水、污泥及噪声,对工业废气、废水及污泥务必进行相对应处理,后剩下来的废水、污泥还需要有的趋势。因此对含油污泥处理解决企业的监管环节,包括了储存、加工过程及污染处理机器设备

Oily sludge treatment: The following describes the following oily sludge treatment process overview

At present, the key processes selected by Chinese oily sludge treatment and solution enterprises are: heat treatment process, hot washing, catalytic cracking, caustic, centralized incineration treatment and preparation of flotation agent. The above treatment solution will lead to industrial waste gas, waste water, sludge and noise in the condition of oily sludge storage and treatment solution. The industrial waste gas, waste water and sludge must be treated accordingly, and then the remaining waste water and sludge still need some trends. Therefore, the supervision of oil sludge treatment enterprises includes storage, processing and pollution treatment machinery and equipment

  • 分类:行业新闻
  • 作者:
  • 来源:
  • 发布时间:2022-10-13
  • 访问量:0
详情

  污油泥处理:下面介绍下含油污泥处理工艺概述

    Oily sludge treatment: The following introduction of oily sludge treatment process overview

  目前,中国含油污泥处理解决企业所选用的关键工艺有:热处理工艺、热洗、催化裂解、苛化、集中焚烧处理及制得浮选剂。之上处理解决企业在含油污泥储存、处理解决的状况下会导致工业废气、废水、污泥及噪声,对工业废气、废水及污泥务必进行相对应处理,后剩下来的废水、污泥还需要有的趋势。因此对含油污泥处理解决企业的监管环节,包括了储存、加工过程及污染处理机器设备、空气污染源趋势等。

    At present, the key processes selected by Chinese oily sludge treatment and solution enterprises are: heat treatment process, hot washing, catalytic cracking, caustic, centralized incineration treatment and preparation of flotation agent. The above treatment solution will lead to industrial waste gas, waste water, sludge and noise in the condition of oily sludge storage and treatment solution. The industrial waste gas, waste water and sludge must be treated accordingly, and then the remaining waste water and sludge still need some trends. Therefore, the supervision of oil sludge treatment enterprises includes storage, processing and pollution treatment machinery and equipment, air pollution source trends, etc.

  1.热处理—资源化再生工艺处理

     Heat treatment-resource regeneration process

  热处理工艺资源化再生工艺处理以网络资源化作重要目的,加工工艺整个过程通常是将含油污泥升温至一定气温,在搅拌下加上热处理工艺药品并体现一定时间后,进入叠螺脱水机(或固液分离机)进行非均相分离出来,液体(水和油化学物质)与含油污泥存储池里的高层液体一并举到水和油收集罐;处理后所造成的污泥委托其他公司或自行处理解决。

   The main purpose of the heat treatment process is to turn network resources into resources. The whole process of the processing process is usually to heat up the oily sludge to a certain temperature, add heat treatment process drugs under stirring and reflect for a certain period of time, then enter the spiral dehydrator (or solid-liquid separator) for heterogeneous separation. The liquid (water and oil chemicals) is lifted together with the high-level liquid in the oily sludge storage tank to the water and oil collection tank; After treatment, the sludge caused by the commission of other companies or their own treatment.

  2.升温—三相分离工艺

      Heating - three phase separation process

  升温—三相分离工艺以回收含油污泥里的原油为关键目的,是含油污泥资源化再生再造处理技术性的之一。加工工艺整个过程通常是将含油污泥加上相匹配处理药品并用蒸汽(或者沸水)马上(或者间歇性)升温至80-90℃后,再应用三相分离设备进行三相分离出来,回收在里面的油;分离出来出废水处理验收合格后一部分回用别的返排;处理后所造成的污泥委托其他公司或自行处理解决。

    The temperature-three phase separation process is one of the technologies of oil sludge recycling and recycling, with the key purpose of recovering crude oil from oily sludge. The whole process is usually the oily sludge plus matching treatment drugs and steam (or boiling water) immediately (or intermittently) heated to 80-90℃, and then the application of three-phase separation equipment for three-phase separation, recovery in the oil; After the separation of wastewater treatment acceptance, part of the waste water can be reused for other back discharge; After treatment, the sludge caused by the commission of other companies or their own treatment.

  3.热洗—三相分离工艺

      Hot washing - three phase separation process

  热洗—三相分离工艺以回收含油污泥里的原油、降低含油污泥里的含油率为重要目的,是含油污泥资源化再生再造、无害化处理技术性的之一。加工工艺整个过程关键在于在反应罐加上污泥量3-4倍容量水(含有一定质量浓度的表活剂),再换蒸汽(或者沸水)马上(或者间歇性)升温至80-90℃后,将含油污泥用泵提升至三相分离出来罐,搅拌一定时间(20-30min)后静放,回收在里面的油;分离出来出废水处理验收合格后一部分回用别的返排;处理后所造成的污泥委托其他公司或自行处理解决。

    The process of hot washing and three-phase separation is one of the technologies for the recovery of crude oil in oily sludge and the reduction of oil content in oily sludge. Processing technology is the key to the whole process in the reaction tank with three to four times the capacity of water quantity of sludge (containing a certain mass concentration of surface active agent), then change the steam (or boiling) (or intermittent) immediately after heating to 80-90 ℃, use oily sludge pump up to the three phase separation pot, stir after a certain time (20-30 min) is static, recovery in oil; After the separation of wastewater treatment acceptance, part of the waste water can be reused for other back discharge; After treatment, the sludge caused by the commission of other companies or their own treatment.

  4.热处理—催化裂解工艺处理

      Heat treatment-catalytic cracking process

  热处理工艺—催化裂解工艺处理以回收含油污泥里的原油、降低含油污泥里的含油、水分含量为关键目的,是含油污泥资源化再生再造、无害化处理技术性的之一。加工工艺整个过程关键在于在热处理工艺——三相分开的大部分,水分含量低于的含油污泥送往催化裂解处理机器设备,催化裂解所造成的水、天然气经致冷后回收;分离出来出废水处理验收合格后一部分回用别的返排;处理后所造成的污泥委托其他公司或自行处理解决。

   The heat treatment-catalytic cracking process is one of the key technologies for the recovery of crude oil in oily sludge and the reduction of oil and water content in oily sludge. The key to the whole process of processing technology lies in the heat treatment process - three-phase separate most of the moisture content is lower than the oily sludge sent to the catalytic cracking treatment machine equipment, catalytic cracking caused by water, natural gas after cooling recovery; After the separation of wastewater treatment acceptance, part of the waste water can be reused for other back discharge; After treatment, the sludge caused by the commission of other companies or their own treatment.

  污油泥处理:今日小编就不再做过多的讲解了,如果您还在污油泥处理而发愁,可以咨询我们厂家,我们是专业的污油泥处理的公司,定会让你满意。

    Sludge treatment: Today Xiaobian will no longer do too much explanation, if you are still worried about sludge treatment, you can consult our manufacturers, we are a professional sludge treatment company, will make you satisfied.

 

关键词:

扫二维码用手机看

碟片式离心机的使用技巧(The use of disc centrifuge skills)
 碟片式离心机是一种新型的离心分离机,它是由一个碟状盘片和一个完整的离心机组成的。这种离心机具有高精度、低噪音等优点,它可以实现高浓度悬浮物的有效分离。由两个部分组成:碟片和完整的离心机。 Disk-type centrifuge is a new type of centrifuge, which is composed of a disk-like plate and a complete centrifuge. The centrifuge has the advantages of high precision and low noise, and it can realize the effective separation of high concentration of suspended matter. It consists of two parts: the disc and the complete centrifuge.
查看详情 白箭头 黑箭头
碟片式离心机的主要结构概述 (Overview of the main structure of disc centrifuge)
碟片式离心机的主要结构概述   碟片式离心机主要由进出口装置、滚筒、盖子、立轴、水平轴、底座、电机和自动控制箱组成。 Overview of the main structure of disc centrifuge Disc centrifuge is mainly composed of import and export device, drum, cover, vertical shaft, horizontal shaft, base, motor and automatic control box. 1. Import and export equipment In addition to visually viewing the liquid conditions before and after separation of the disk-type centrifuge, the inlet and outlet devices can also be adjusted by regulating the flow control valve on the device to adjust its separation effect. A sampling device is installed on the upper part of the cover to realize water separation through sampling and testing.   1.进出口设备   除了直观地看到碟片式离心机分离前后的液体状况外,入口和出口装置还可以通过调节装置上的流量调节阀来调节其分离效果。机盖上部安装有取样装置,通过取样和测试实现水分离。
查看详情 白箭头 黑箭头
碟片式离心机的原理是什么?(What is the principle of disc centrifuge?)
碟片式离心机的原理是什么?   按功能可分为固液分离型和固液分离型两种。固液两用碟片式离心机是碟片式离心机之一。它是一种效率高、产量大、自动化程度高的先进设备。碟片式离心机仅适用于分离固体含量低的悬浮液和比重差小的互不溶性液体。 What is the principle of disc centrifuge? According to the function can be divided into solid-liquid separation type and solid-liquid separation type two. Solid - liquid dual - purpose disc centrifuge is one of the disc centrifuges. It is a kind of advanced equipment with high efficiency, large output and high degree of automation. Disc centrifuge is only suitable for separating suspension with low solid content and insoluble liquid with small specific gravity difference.
查看详情 白箭头 黑箭头
莫尼亚

南京莫尼亚离心机科技发展有限公司

联系人:   陈永欣 18013325671 

                 徐锋    18013035671

售后服务: 赵士波 18013344029
电话/传真:025-58474011
邮箱: molniya@126.com

网址:www.njmoniya.cn
公司地址:江苏省南京市六合区竹镇工业园凌峰路71号

General Sales Agent for Iran, Iraq and Syria:

Company: ROYESH BEDONE MAX.LTD

Contact: Mr. GHASEM AMANI

Telephone number: 0098 912 111 2893

Mail box: robimaxfactory@gmail.com

莫尼亚

- 手机版  莫尼亚 -

Copyright © 2019 南京莫尼亚离心机科技发展有限公司

网站建设:中企动力 南京

苏ICP备2020058610号-1

SEO 标签