离心机厂家:介绍如何解决离心机的腐蚀? (Centrifuge manufacturer: How to solve centrifuge corrosion?
- 分类:行业新闻
- 作者:
- 来源:
- 发布时间:2023-01-11
- 访问量:0
【概要描述】 离心机厂家:介绍如何解决离心机的腐蚀
为了避免腐蚀机安全隐患的产生,扭头使用时应当注意离心管架的试品充注量及封闭的密封性,常常查验密封环是不是完好无损。如果出现衰老、损坏应定期更换,防止出现漏油,避免有浸蚀作用的有机溶剂与扭头接触。
Centrifuge manufacturer: How to solve centrifuge corrosion
In order to avoid the production of corrosion machine safety risks, the use of the torsion head should pay attention to the sample filling amount and sealing sealing of the centrifugal tube holder, and often check whether the sealing ring is intact. If there is aging, damage should be replaced regularly, to prevent oil leakage, to avoid the erosion of organic solvents and torsion head contact.
离心机厂家:介绍如何解决离心机的腐蚀? (Centrifuge manufacturer: How to solve centrifuge corrosion?
【概要描述】 离心机厂家:介绍如何解决离心机的腐蚀
为了避免腐蚀机安全隐患的产生,扭头使用时应当注意离心管架的试品充注量及封闭的密封性,常常查验密封环是不是完好无损。如果出现衰老、损坏应定期更换,防止出现漏油,避免有浸蚀作用的有机溶剂与扭头接触。
Centrifuge manufacturer: How to solve centrifuge corrosion
In order to avoid the production of corrosion machine safety risks, the use of the torsion head should pay attention to the sample filling amount and sealing sealing of the centrifugal tube holder, and often check whether the sealing ring is intact. If there is aging, damage should be replaced regularly, to prevent oil leakage, to avoid the erosion of organic solvents and torsion head contact.
- 分类:行业新闻
- 作者:
- 来源:
- 发布时间:2023-01-11
- 访问量:0
离心机厂家:介绍如何解决离心机的腐蚀
Centrifuge manufacturer: How to solve centrifuge corrosion
为了避免腐蚀机安全隐患的产生,扭头使用时应当注意离心管架的试品充注量及封闭的密封性,常常查验密封环是不是完好无损。如果出现衰老、损坏应定期更换,防止出现漏油,避免有浸蚀作用的有机溶剂与扭头接触。扭头用后一定要清洗、擦洗并喷漆保护膜,擦抹维护植物油脂。
In order to avoid the production of corrosion machine safety risks, the use of the torsion head should pay attention to the sample filling amount and sealing sealing of the centrifugal tube holder, and often check whether the sealing ring is intact. If there is aging, damage should be replaced regularly, to prevent oil leakage, to avoid the erosion of organic solvents and torsion head contact. After turning the head, be sure to clean, scrub and spray paint protective film, wipe maintenance plant grease.
机械性损伤也是导致扭头损害造成浸蚀的一种缘故。因而扭头应用、储存中应尽可能避免扭头被磕伤、擦破、划伤避免造成设备毁坏。扭头储存的自然环境应保持清洁,放置专用型柜子上,放进柜内或放进配有吸潮硅橡胶的烘干机内。以防止欠佳自然环境对砖块导致浸蚀,减少扭头的使用期。
Mechanical damage is also a cause of erosion caused by torsion damage. Therefore, in the application and storage of the torsion head, it should be avoided as far as possible to knock, scratch and scratch the torsion head to avoid damaging the equipment. The natural environment of torsion head storage should be kept clean, placed on the special cabinet, put into the cabinet or put into the dryer equipped with moisture absorbing silicone rubber. In order to prevent the poor natural environment to the brick erosion, reduce the life of the torsion head.
离心机浸蚀难题,如今为大家推荐4中避免也可以缓解离心机浸蚀的四个对策。
Centrifuge erosion problem, now recommend four measures to avoid or alleviate centrifuge erosion.
一、选好材质离心机至关重要因为不同原材料及分离出来规定,需要采用不同类型的型号。型号及主参数确认后,针对不同设备在不一样环境下的耐蚀性能,综合性其物理化学特J生,性价比高等多种因素,从基本面分析上明确抗压强度零件原材料。从原材料自身来说,它选择的总体目标原材料十分安全。
Selecting the right material for the centrifuge is very important because different materials and separation regulations require different types of models. After confirming the models and main parameters, the raw materials of compressive strength parts are defined from the fundamental analysis according to the corrosion resistance performance of different equipment in different environments, comprehensive physical and chemical characteristics, high cost performance and many other factors. From the raw material itself, the overall target material it chooses is very safe.
二、离心机的机构设计,一个好的设计能增加设备使用年限,保证机器设备安全性,针对总体设计,非常容易加快浸蚀的设计问题是应力趋向和间隙自然环境,有时候虽然金属材料侵泡水溶液,腐蚀率比较小;但产生间隙,因为内部结构水溶液的化工和化学情况出现了改变,将造成很严重的韧性断裂。
Centrifuge mechanism design, a good design can increase the service life of the equipment, ensure the safety of the machine equipment, for the overall design, it is very easy to accelerate the corrosion design problem is the stress trend and gap natural environment, sometimes although metal materials soaked water solution, corrosion rate is relatively small; However, due to the change of chemical and chemical conditions of the aqueous solution of the internal structure, the gap will cause serious ductile fracture.
三、离心机表面预防措施 Centrifuge surface precautions
操纵浸蚀的一个理论依据便是阻隔浸蚀自然环境。在离心机设计里,常常选用表层处理的方法,如法兰盘、热镀锌、不锈钢、有机化学涂层等方法,这个方法在很多环境里是有用的,但是对于转动零件,应该注意一个重要的状况:基体与涂层是两个原材料,其热膨胀系数是不一样的,将于转动件压缩变形后产生不一样的应力,进而造成大量微裂纹的形成;若上述情况情况的存有,将加快浸蚀产生。因而,针对转动零件的表层安全防护方式,应慎重选用。
One theoretical basis for manipulative erosion is to block the natural environment. In centrifuge design, surface treatment methods are often used, such as flanges, hot dip galvanizing, stainless steel, organic chemical coating methods, this method is useful in many environments, but for rotating parts, we should pay attention to an important situation: Matrix and coating are two raw materials, whose thermal expansion coefficient is not the same, will produce different stress after compression deformation of rotating parts, and then cause the formation of a large number of microcracks; If the above conditions exist, the erosion will be accelerated. Therefore, the surface safety protection of rotating parts should be carefully selected.
四、应用脱硫剂离心机自身涉及到跨学科,需要使用好离心机,除了上述一些对策外,还应当注意科学研究其应用场景。脱硫剂的应用,在实际应用中,也很多选用。对于某些恶劣的环境,选用适度的脱硫剂就能让零件做到适用水平,只需加工工艺批准,脱硫剂的选用,应当是离心机运用的一条合理之途。通过上述4点能够给离心机一个很好的维护,更为抗腐蚀,使离心机所使用的更为长期,安全。
The application of desulfurizer centrifuge itself involves interdisciplinary, need to use centrifuge well, in addition to the above countermeasures, should also pay attention to scientific research of its application scenarios. The application of desulfurizer, in the practical application, also a lot of choice. For some harsh environment, the selection of moderate desulfurizer can make the parts applicable level, as long as the processing technology approval, the selection of desulfurizer, should be a reasonable way to use centrifuge. Through the above four points can give the centrifuge a good maintenance, more corrosion resistance, so that the centrifuge is used for a longer time, safety.
离心机厂家:谢谢大家的收看,我公司有各种离心机,如果您有需要可以咨询我们离心机厂家。
Centrifuge manufacturers: Thank you for watching, our company has a variety of centrifuges, if you need to consult our centrifuge manufacturers.
扫二维码用手机看
南京莫尼亚离心机科技发展有限公司
联系人: 陈永欣 18013325617
徐锋 18013035617
售后服务: 赵士波 18013344029
电话/传真:025-58474011
邮箱: molniya@126.com
网址:www.njmoniya.cn
公司地址:江苏省南京市六合区竹镇工业园凌峰路71号
General Sales Agent for Iran, Iraq and Syria:
Company: ROYESH BEDONE MAX.LTD
Contact: Mr. GHASEM AMANI
Telephone number: 0098 912 111 2893
Mail box: robimaxfactory@gmail.com
- 手机版 莫尼亚 -