污油泥处理技术设备厂家企业生产的水平卧式离心机的正常维护是防止事故和部件损坏的重要方面，使用时应遵守以下指标：
(1)圆锥屏
屏幕内表面必须是精确的锥形，并确保像刮刀一样的距离间隔，使屏幕内表面均匀磨损，部分磨损会降低卧式离心机体的寿命。
因此，煤在脱水机里只停留一秒钟。如果水不能及时从筛孔过滤，就会与煤一起排出，降低脱水效果，因此要经常检查筛孔是否堵塞。
(2)螺旋卸载转子(4061-1P)
随着刮板逐渐磨损，刮板边缘和筛板之间的间距也增加，脱水性能下降，为了确保2.5-3mm的正常间距，污油泥处理技术设备厂家在主轴肩膀上有一套曹征垫，每个垫片的厚度为1mm，每次从上到下移动垫片时，升高整个螺旋装卸机，刮煤
(3)贝尔盖(4051-101)
由于煤的磨损，钟形罩和肩膀迅速磨损，平衡破裂，需要经常检查磨损程度，过度磨损的部分，焊接金属层，焊接时防止弯曲变形，焊接后必须进行平衡实验。
(4)齿轮传动装置
为了确保卧式离心机齿轮的正常传动，必须注意润滑情况。桌面离心机油供应不足会损坏齿面，太多油会过热，齿轮工作面会发生金属脱皮现象，因此不允许齿轮箱装满润滑油，尤其是拆卸内部零件时要更加小心。为了检查齿轮运行状态，下部壳体上有两个窥视孔。

The normal maintenance of horizontal centrifuges produced by enterprises is an important aspect to prevent accidents and damage of components. The following indexes should be observed when using them:
(1) cone screen
The screen inner surface must be precisely tapered and ensure a spater-like distance separation so that the screen inner surface is uniformly worn, partial wear will reduce the life of the horizontal centrifugal body.
So the coal stays in the dehydrator for only a second.
If the water is not filtered through the screens in time, it will be drained along with the coal, reducing the effect of dehydration, so check the screens frequently for blockage.
(2) Spiral unloading rotor (4061-1P)
Wear gradually as scraper, scraper spacing between edge and sieve plate will increase, dehydration performance degradation, in order to ensure the normal spacing of 2.5 3 mm, sewage sludge treatment technology and equipment manufacturers in a set of cao on the main shaft shoulder pad, each of the gasket thickness is 1 mm, each moving from top to bottom gasket, increase the whole screw loading and unloading machine, coal
(3) Berge (4051-101)
Due to coal wear, bell jar and shoulder wear rapidly, balance rupture, need to check the wear degree, excessive wear part, welding metal layer, welding to prevent bending deformation, after welding must be carried out balance experiment.
(4) Gear transmission device
In order to ensure the normal transmission of horizontal centrifuge gear, we must pay attention to lubrication.
Too much oil will overheat. Metal peeling will occur on the gear face. Therefore, do not allow the gear box to be filled with oil, especially when removing internal parts.
In order to check the operating state of the gear, there are two peepholes in the lower housing.