啊啊

NEWS CENTER

新闻动态

您现在的位置:
首页
/
/
/
碟片式离心机的安装注意事项 (Installation precautions of disc centrifuge)

碟片式离心机的安装注意事项 (Installation precautions of disc centrifuge)

  • 分类:离心机
  • 作者:南京莫尼亚离心机科技发展有限公司
  • 来源:http://www.njmoniya.cn/
  • 发布时间:2020-11-11
  • 访问量:0

【概要描述】碟片式离心机​的现场进行安装的时候我们一般都带有一个专用底座和四根地脚螺栓,按着安装设计说明要求直接将底座找平,然后再将底座和离心机主体按着由下向上的顺序相连即可,但是对于一般的这样一种方法可以安装完毕后离心机转股的立轴上端的圆周跳动度达不到要求。

Disc centrifuge on site for the installation time we usually comes with a special base and four anchor bolt, according to the installation specification of leveling request directly to the base, then the base and the centrifuge can be connected to main body according to the order of the from down to up, but for the average of such a method can be installed after the completion of the centrifuge convertible the circumference of a circle at the top of the vertical shaft of beating degree can not meet the requirements.

碟片式离心机的安装注意事项 (Installation precautions of disc centrifuge)

【概要描述】碟片式离心机​的现场进行安装的时候我们一般都带有一个专用底座和四根地脚螺栓,按着安装设计说明要求直接将底座找平,然后再将底座和离心机主体按着由下向上的顺序相连即可,但是对于一般的这样一种方法可以安装完毕后离心机转股的立轴上端的圆周跳动度达不到要求。

Disc centrifuge on site for the installation time we usually comes with a special base and four anchor bolt, according to the installation specification of leveling request directly to the base, then the base and the centrifuge can be connected to main body according to the order of the from down to up, but for the average of such a method can be installed after the completion of the centrifuge convertible the circumference of a circle at the top of the vertical shaft of beating degree can not meet the requirements.

  • 分类:离心机
  • 作者:南京莫尼亚离心机科技发展有限公司
  • 来源:http://www.njmoniya.cn/
  • 发布时间:2020-11-11
  • 访问量:0
详情

碟片式离心机

 

 

  碟片式离心机的现场进行安装的时候我们一般都带有一个专用底座和四根地脚螺栓,按着安装设计说明要求直接将底座找平,然后再将底座和离心机主体按着由下向上的顺序相连即可,但是对于一般的这样一种方法可以安装完毕后离心机转股的立轴上端的圆周跳动度达不到要求,这主要是底座在找水平的时候累计误差太大,比如基础数据平面结构不够平,垫铁与底座接触时间不够严密,碟片式离心机底座的水平度按普通技术标准管理规范发展已经成为不能得到满足社会要求,这就导致需要不断提高系统安装位置精度,以我多年历史经验将底座水平度控制在0.07-0.08mm/m,主轴上端圆周跳动度控制在0.02-0.03mm,这个精度范围内设备安全运行是平稳,噪声也小。

Disc centrifuge on site for the installation time we usually comes with a special base and four anchor bolt, according to the installation specification of leveling request directly to the base, then the base and the centrifuge can be connected to main body according to the order of the from down to up, but for the average of such a method can be installed after the completion of the centrifuge convertible the circumference of a circle at the top of the vertical shaft of beating degree can not meet the requirements, this is primarily to base in search of the cumulative error is too large, such as basic data plane structure is not flat, shim and the base contact time is not tight. Disc centrifuge the levelness of the base according to general technical standard management specification development has become a cannot satisfy the social requirement, this leads to need to constantly improve the system installation location precision, in my many years of experience in history will be the base level control in 0.07 0.08 mm/m, spindle upper circumferential beating degree of control in 0.02 0.03 mm, the accuracy within the scope of the safe operation of the equipment is steady, the noise is small.

 

 

增加四个地脚螺栓,用钢板穿新地脚螺栓,注意螺纹部分不能超过2-3螺距,用压缩空气清洗离心机基础,特别是地脚螺栓孔部分,在基础上洒少量水但不能使基础水,基础上的水在吸收干燥快时可以灌浆,在基础上重新测试平面,以保证基础的平整度,然后调整碟片式离心机每组垫铁的标高水平仪,使同一设备基础上垫铁的高度差在允许偏差范围内,24小时后,用早期强度无收缩的CGM灌浆材料填充地脚螺栓孔与基础和铁板之间的空间后,早期强度灌浆材料将达到强度。 这种灌浆材料具有良好的流动性能,可以填补碟片式离心机每一个间隙,保证铁板与灌浆材料的紧密接触,增加整体稳定性。

Add four anchor bolt, with steel plate wear new anchor bolt, and pay attention to the threaded portion is no more than 2-3 pitch, clean with compressed air centrifuge, especially the anchor bolt hole part, on the basis of sprinkle a little water but cannot make water based, on the basis of water while grouting absorption of quick drying, on the basis of retest plane, to ensure the smoothness of foundation, and then adjust the disc centrifuge mat iron level in each group level, make the same equipment on the basis of shim height difference in the range of the allowable deviation after 24 hours, with early strength non-shrinkage CGM grout material filling anchor bolt hole and the space between the base and iron plate.  The early strength grouting material will reach strength. This grout material has good flow performance and can fill every gap of disc centrifuge to ensure the close contact between iron plate and grout material and increase the overall stability.

关键词:

扫二维码用手机看

碟片式离心机的使用技巧(The use of disc centrifuge skills)
 碟片式离心机是一种新型的离心分离机,它是由一个碟状盘片和一个完整的离心机组成的。这种离心机具有高精度、低噪音等优点,它可以实现高浓度悬浮物的有效分离。由两个部分组成:碟片和完整的离心机。 Disk-type centrifuge is a new type of centrifuge, which is composed of a disk-like plate and a complete centrifuge. The centrifuge has the advantages of high precision and low noise, and it can realize the effective separation of high concentration of suspended matter. It consists of two parts: the disc and the complete centrifuge.
查看详情 白箭头 黑箭头
碟片式离心机的主要结构概述 (Overview of the main structure of disc centrifuge)
碟片式离心机的主要结构概述   碟片式离心机主要由进出口装置、滚筒、盖子、立轴、水平轴、底座、电机和自动控制箱组成。 Overview of the main structure of disc centrifuge Disc centrifuge is mainly composed of import and export device, drum, cover, vertical shaft, horizontal shaft, base, motor and automatic control box. 1. Import and export equipment In addition to visually viewing the liquid conditions before and after separation of the disk-type centrifuge, the inlet and outlet devices can also be adjusted by regulating the flow control valve on the device to adjust its separation effect. A sampling device is installed on the upper part of the cover to realize water separation through sampling and testing.   1.进出口设备   除了直观地看到碟片式离心机分离前后的液体状况外,入口和出口装置还可以通过调节装置上的流量调节阀来调节其分离效果。机盖上部安装有取样装置,通过取样和测试实现水分离。
查看详情 白箭头 黑箭头
碟片式离心机的原理是什么?(What is the principle of disc centrifuge?)
碟片式离心机的原理是什么?   按功能可分为固液分离型和固液分离型两种。固液两用碟片式离心机是碟片式离心机之一。它是一种效率高、产量大、自动化程度高的先进设备。碟片式离心机仅适用于分离固体含量低的悬浮液和比重差小的互不溶性液体。 What is the principle of disc centrifuge? According to the function can be divided into solid-liquid separation type and solid-liquid separation type two. Solid - liquid dual - purpose disc centrifuge is one of the disc centrifuges. It is a kind of advanced equipment with high efficiency, large output and high degree of automation. Disc centrifuge is only suitable for separating suspension with low solid content and insoluble liquid with small specific gravity difference.
查看详情 白箭头 黑箭头
莫尼亚

南京莫尼亚离心机科技发展有限公司

联系人:   陈永欣 18013325671 

                 徐锋    18013035671

售后服务: 赵士波 18013344029
电话/传真:025-58474011
邮箱: molniya@126.com

网址:www.njmoniya.cn
公司地址:江苏省南京市六合区竹镇工业园凌峰路71号

General Sales Agent for Iran, Iraq and Syria:

Company: ROYESH BEDONE MAX.LTD

Contact: Mr. GHASEM AMANI

Telephone number: 0098 912 111 2893

Mail box: robimaxfactory@gmail.com

莫尼亚

- 手机版  莫尼亚 -

Copyright © 2019 南京莫尼亚离心机科技发展有限公司

网站建设:中企动力 南京

苏ICP备2020058610号-1

SEO 标签