离心机厂家：净乳机的密封和排渣
       分离筒密封:控制水通过控制阀被导入高速旋转的分离筒中进入活塞下部工作水腔,产生的离心压幼将活塞上推与分离筒盖上的密封环压紧封闭筒壁上的排查口，造成分离工作容腔的密封分离正常进行即密封。
       净乳机分离筒的排渣:控制水通过控制阀被导入作用滑块上腔,产生的离心压力将作用滑块向下压,克服支撑弹簧的压力打开三只浅水阀(尼龙扣，活塞下腔控制水迅速排出，在分离筒内被处理物料的离心压力作用下，活塞下降,积聚的杂质从壁上的排渣口迅速排出。
离心机厂家：净乳机密封程序分解
       净乳机密封---待分离机全速后,将控制阀转到“密封”位置，控制伐芯上的孔与连接导水环的接管连通，控制水经导水环喷入配水挡圈,经分离筒本体上的小孔，在离心压力作用下进入活塞下部水腔，产生的离心压力将活塞上推，紧压在分离筒盖的密封环上。
       离心机厂家：由于活塞下部密封水工作压力大于上部被处理物料的压力，因此造成分离筒工作时的密封状态.当活塞下腔注满水后，继续进入的水通过导水环回水孔道经控制阀接管从指示管流出。指示管出水表明分离筒密封工作已完成.此时应将控制阀手轮箭头转向补偿位置，机器可以开始进料分离工作。


Centrifuge manufacturer: clean milk machine seal and slag
Separation cylinder seal: the control water is imported into the high-speed rotating separation cylinder through the control valve into the lower part of the piston working water chamber, the centrifugal pressure generated will push the piston up and the sealing ring on the separation cylinder cover pressing the inspection port on the closed cylinder wall, resulting in the sealing separation of the separation work cavity is sealed normally.
 

The discharge of the separation cylinder of the cleaning milk machine: the control water is imported into the upper cavity of the acting slide block through the control valve. The centrifugal pressure generated will push the acting slide block down to overcome the pressure of the supporting spring to open the three shallow water valves (nylon buckle, the lower chamber of the piston controls the water to be discharged quickly. Under the centrifugal pressure of the material processed in the separation cylinder, the piston descends and the accumulated impurities are quickly expelled from the drain hole in the wall.
 

Centrifuge manufacturer: clean milk confidential sealing program decomposition
Net milk confidential letters - after being separator at full speed, the control valve to "seal" position, the control of cutting holes on the core control of connected with the connection guide water ring to control the water by the guide ring injection water distribution ring, the bowl of holes on the body, water at the bottom of the centrifugal pressure into the piston chamber, the centrifugal pressure to push on the piston, clamp on the sealing ring of the separating cylinder cover.
Centrifuge manufacturer: Because the working pressure of the sealing water at the lower part of the piston is greater than the pressure of the material being processed at the upper part, the sealing state of the separation cylinder at work is caused.
 

When the lower chamber of the piston is filled with water, the water that continues to enter flows out of the indicator pipe through the backwater channel of the water guide ring through the control valve.
Indicating pipe discharge indicates completion of separation cylinder seal.
At this point, the control valve handwheel arrow should be turned to the compensation position, the machine can start the feed separation work.